Tuesday, January 24, 2012

Basic Differences Between CAT5, CAT5E, CAT6, CAT6e, CAT6a Cables







  RJ45 Pin-out for Network Connection 


Troubleshooting cabling problems in most cases has to be done onsite. A cable technician would have to be at the location to use tools for diagnosing cables such a toner. Desktop and networking hardware that are interconnected by network cables can be remotely access online. Applications such as online desktop support software provides the access into a network over the web from which connection could be tested,  network switching can be configured or diagnosed. 
 

Basic Difference Between CAT5,CAT6,CAT6e and CAT6a Cables
 
Category 5
Category 5 cabling transmits at a frequency of 100MHz. This provides a rated line speed of up to 100Mbit/s and a cable segment length of 100 meters maximum. Most Category 5 cables, were designed for earlier networks replacing cat 3, only used two twisted pairs of wires. However, older Category 5 cabling continues to make up the majority of the world’s network cabling infrastructure.

Category 5e
Category 5e was later introduced as an improved specification to the very popular Category 5 that replaced Cat 3.  The improvement was in noise reduction. By reducing the noise and signal interference beyond Cat 5, Category 5e rated transfer speeds increased to 350 Mbit/s over 100 meters. The new 5e cabling standard however also required all the cabling to include four twisted pairs not just two like with Cat 5. All eight contacts has to be used. Cat 5e introduced and optimized encoding scheme that allows up to 50-meter lengths of Category 5e cable to provide at or near Gigabit Ethernet (1000BASE-T) speeds. This was during the era of the early stages of Gigabit

Category 6
Gigabit Ethernet (1000BASE-T) became mainstream and required new industry-standard cables capable of transmitting at a higher frequencies than Cat 5e to go beyond the 50 meter limitation. Cat 6e transmits at 250 MHz. The new Category 6 cable uses thicker-gauge wire to attain the higher frequencies, it has increased shielding, and more pair twists per inch to reduce signal noise and interference. The new tighter specifications introduced with Cat 6 cabling guarantee that 100-meter runs of Category 6 are capable of 1000 Mbit/s transfer speeds. As with 5e reducing the cable length can achieve higher speeds than the category types design goal so 10-Gigabit Ethernet speeds can be achieved  when reducing cable lengths to less than 50 meters.

Category 6e
The limitation of 50 meters of 10Gigabit was over come with Category 6 Enhanced (6e).  Cat 6e is an augmented specification designed to double transmission frequency of Cat 6 to 500 MHz. It has the more pair twists per inch as does Cat 6 but it's also wrapping Category 6 in grounded foil shielding, a full 10-Gigabit Ethernet speeds can be achieved without sacrificing the max cable length of 100 meters.

Category 6a
Category 6a (or Augmented Category 6) is defined at frequencies up to 500 MHz—twice that of Cat. 6 but he same as 6e. Because it is shielded, Cat 6a performs at improved specifications over 6 and 6e, in particular in the area of alien cross-talk when compared to Cat 6 UTP   Cat 6 UTP exhibited high alien noise in high frequencies.6A. To reduce the noise, 6a EA specification (not EIA/TIA) require a new generation of connecting hardware that offers far superior performance. 6A connectors performs 3 dB better than a Cat 6a connector that conforms with the EIA/TIA specification. 3 dB equates to 100% increase of near-end cross-talk noise reduction. 


More wire specifications and a practical case example use of 10GB is available at this additional location - Differences Between Category 5 and Category 6 . The use of special case cables such as cross-over cables is also covered at the same article location.








11 comments:

Anonymous said...

Thanks for this post. It was just the information I was looking for. This plus another post I found at another site helped me decide that cat 6a cables and wire runs are not worth the added cost. (g)

Anonymous said...

Nice Info....

Structured Cabling said...

Your post about Cat5e vs Cat6 is so nice and this fill someone in on helped me allot-off. You can make more attractive your article with use photo implementation

Sahar Services

Unknown said...

Wonderful post you have shared.. It easily explains the clear differences between the Ethernet cable of different categories... Keep on sharing such knowledgeable posts.

Unknown said...

I am impressed your blog,thanks a lot for sharing this Information.
Antivirus Support Services

Remote-Tech said...

A positive note about cabling is that once you figure out what to do do and how to accomplish the task of doing it, for example making your own cables, those settings and patterns never change. New standards can be added and new faster standards with new cabling but the RJ45 connector and the wiring of patch cables still remains a constant and has been the same for many years now. Cabling in many cases is self support. except for large wiring projects, cables can be made on-site. Supporting cabling can require some additional tools such as toners and cable testers.

Anonymous said...

How about if u use cat6a to lower MHz is okay?

Arnoldpeter said...

Differentiation between Cat6 and Cat5e Cables are awesome, Using this we can choose a particular cable for the network cabling systems which is exactly suits for. This post is very Informative. Thanks for Sharing this post. Keep Sharing

If you want to know more about on cat5e Cables Click Here
Cat5e Cables

SFCable said...

I appreciate your Blog it got Some Informative Stuffs on Cat6 and Cat5e cabling systems. Nice Article Thanks For Sharing this. Keep Posting

DINTEK Electronic Limited said...

Very informative!! Thanks for sharing this.

If you are looking for a cat6a plug then Dintek Electronic Ltd is the right place. Our industrial-grade Cat.6A RJ45 field plugs have been designed for easy installation and field termination while being contained in a rugged package. For more visit our website: www.dintek.com.tw

Joe Roberts said...

Your blog is very interesting thanks for sharing. Cat5e Plenum is a premium Ethernet cable that is well suited for use in applications with data transmission rates of 1 Gbps and 100 Mbps. It offers outstanding performance and good flexibility, which provides the user with an excellent return on investment option for commercial and residential installations.
Cat5e Plenum Cable